ACCESSORIES / OPTIONAL
HBV-180 crusher
Vegetable crusher designed for the maintenance of green spaces, meadows, fields or roadside cutting width 1800, thanks to its biomass recovery system the waste thus produced is directly sent into the recovery bin provided for this purpose. Ideal for the regeneration of your meadows or land left fallow.
HBOX-5.00 Waste Trailer
It makes it possible to collect and recycle waste resulting from forest crushing or maintenance waste from green spaces. Our tilting HBOX-5.0 is made of steel. It is mounted on 2 cylinders facilitating the emptying of the bucket. The capacity of our bucket is 5m3. Coupled with a front linkage, you can mount a crusher on the front of your HT100 and collect waste directly through a conveyor spilling chips and produced in the recovery bin mounted on the back of our chase. These devices allow you to work while enhancing your waste and leaving the floor clean.
Agricultural Double Translation Tool Holder H-POL
This adaptation of agricultural tools carrier answers all needs of attachment of tools in system 3 points, it allows to take the tool on the ground, to raise it and to translate it forward to optimize the balance of all. This device makes it possible to supply a fertilizer distributor without sophisticated lifting equipment.
Our agricultural tool tractor H-POL is also equipped with two single or double acting dispensers that can be connected by push-pull. This agricultural tool holder is a lifting tool allowing a horizontal and vertical rear translation movement with electro dispenser.
This agricultural tool carrier system is intended for farmers who do not have in their possession lifting equipment to bring equipment type seed drill, fertilizer spreader or nitrogen at the height of the rear tray of the carrier to caterpillar to position it on the simple tool holder.It’s a 2 in 1 solution that solves rear lift problems. It will allow you to save on your investments, since it solves the lifting of the agricultural equipments that you will seek to install on our crawler carrier: Simple and effective.
Our HPOL tool holder is directly controlled from inside the cab thanks to an internal Joystick control, but you can also operate it thanks to a transfer of commands via an external remote control box connected to the cab, on the side of the cab. our chases . You can thus closely monitor the lifting operations of the tool.
Discover also our other accessories and our Extract vine puller.
Power Mirrors
Your chaser can be equipped on request with electric mirrors. They are mounted on electric telescopic arms diameter 20 mm. The mirrors are equipped with a de-icing electric main mirror and a de-icing wide-angle mirror only.
Full Protection Case
Your chaser can be equipped, on request, with 4.00 mm thick aluminum protective guards, which are held under the frame by stainless steel screws, to protect all the bodies at the bottom of the crates of our HT100 chase. The wheel motors, the engine, the axles are thus protected from the rising of mud of the stumps or stones which can damage the good functioning of our chase. We advise you to opt for the complete protective casings when you use the HT100 in moderately difficult environments such as very muddy, forest or rocky environments.
Full Shielding Sheets
Your chaser can be equipped on request with 6.00 mm thick aluminum armor plates held under the frame by stainless steel screws, in order to protect all the bodies at the bottom of the crates of our HT100 chase. The wheel motors, the engine, the axles are thus protected from rising mud, stumps or stones that can damage the good functioning of our chase. We advise you to opt for the complete shield plates when using the HT100 in very difficult environments such as forest or rocky environments.
Vibration damping system on bogies
A vibration damping system on bogies mounted on silentblocs is available. It helps to partially absorb the vibrations caused by the contact of the tracks on the road. It improves driver comfort in the cabin.
Air conditioning Cabin with particle filter
On request you can choose to equip your chaser tractor with an air conditioning system. The air conditioning unit is equipped with a SADEN brand compressor and a DEUTZ dehydrator, and particulate filter. Three-speed fan button. The fresh air is evenly distributed throughout the cabin and will improve your working comfort whatever the weather.
Extensions Alu backboard checkerboard
A single tray is provided as standard equipment. On request, extensions can be added. They thus cover the caterpillars and limit the sludge lifts on the plateau.
Pressurization Cabin with carbon filter
To allow you to work safely and without personal protection, we offer a system of pressurization of the cabin. The interior of the cabin is put under a pressure higher than that of the outside to avoid any entry of particles harmful for the man. The forced air in the cabin is “cleaned” by a charcoal filter system.
Front linkage
This device allows to hitch up all the tools configured in 3-point hitch. The 1000 rpm power take-off is mounted directly on the DEUTZ engine and controlled from inside the cabin by joystick.
HBOX-3.5 Waste recovery bucket
It makes it possible to collect and recycle waste resulting from forest crushing or maintenance waste from green spaces. Our HBOX3.5 is made of stainless steel 2.00 mm. It is equipped with a tilting door, mounted on 2 cylinders facilitating the emptying of the bucket. The capacity of our skip is 3.5m 3 sup>. Coupled with a front linkage, you can mount a crusher on the front of your HT100 and collect waste directly from a conveyor that dumps the resulting chips into the recovery bin mounted on the back of our chase. These devices allow you to work while enhancing your waste and leaving the floor clean.
MORE INFO
If you want more information, fill out this form.
We will get back to you as soon as possible.
COME ON SITE
BUSINESS HOURS
Monday to Thursday 8:00 am-12:00 pm / 1:30 pm - 5:00 pm
Fridayi 8:00 am-12:00 pm
PLACE
ZA La Haute Sarrazine
6 rue de la Bonne Chauffe
16100 COGNAC
CONTACT

